MicroSL100 series: Silicon Photomultiplier, 20 m (1296) microcells, 1mm circular diameter, Ceramic Package, Epoxy Fill

Additional details are available HERE

MicroSL100 series: Silicon Photomultiplier, 20 m (576) microcells, 1mm circular diameter, Ceramic Package, Epoxy Fill

Additional details are available HERE

MicroSL100 series: Silicon Photomultiplier, 20 m (324) microcells, 1mm circular diameter, Ceramic Package, Epoxy Fill

Additional details are available HERE

MicroSL100 series: Silicon Photomultiplier, 20 m (90) microcells, 1mm circular diameter, Ceramic Package, Epoxy Fill

Additional details are available HERE

MicroSL300 series: Silicon Photomultiplier, 35um (4774) microcells, 3mmx3mm sensor, Ceramic Package, Epoxy Fill

Additional details are available HERE

MicroSL600: Silicon Photomultiplier, 35 m (19069) microcells, four 3mm x 3mm sensors arranged in 2x2 configuration, Summed Output, Ceramic Package, Epoxy Fill

Additional details are available HERE

The Array4SL incorporates a 4 x 4 matrix of 8.12 mm2 sensitive area SL family SPM detectors optimized for the 420nm~700nm spectral range. Each SPM is mounted with a pixel pitch of 3.37mm. This matrix is supported by a four side scalable, nonmagnetic ceramic package with a 15.81 x 15.31 mm2 footprint.

Additional data sheet details are located HERE.

MicroSL Family Transimpedance Amplifier and Power Supply Board Option for use with 1mm SensL MicroSL detectors.

PLEASE NOTE: If you are ordering 3mm detectors (i.e. MicroSL-30035) you will need to order the Micro-EVB-3mm board.

See MicroSL Family Datasheet for additional details.

MicroSL Family Transimpedance Amplifier and Power Supply Board Option for use with 3mm SensL MicroSL detectors.

PLEASE NOTE: If you are ordering 1mm detectors (i.e. MicroSL-10035) you will need to order the Micro-EVB-1mm board.

See MicroSL Family Datasheet for additional details.

ArraySL-4p9 is a low cost 144 pixel, position sensitive low light detector integrating SensL ArraySL4 ceramic packaged silicon photomultipliers. 

See the Product Brief for a more detailed product description

SL Micro Family -- Silicon Photomultiplier Scintillator Pack with 3 detectors and crystals

The ArraySL-4 can be ordered with the option of a 16-channel preamplifier board (Array4-EVB-PreAmp) that provides differential voltage outputs for each of the pixels in the array. The preamplifiers are implemented using Analog Device’s AD8132 chips. 

This product works with the Array4-EVB-PixOut (Sold Separately). 

Additional details are available in the ArraySL Data Sheet.

An additional option available for the ArraySL-4 is the evaluation board (Array4-EVB-PixOut). It connects to the preamplifier described above via the 80-way board-to-board connector then makes the output signals available via SMA connectors for fast and easy evaluation, e.g. via osciloscope. It has the additional benefit of being able to extract either a single, summed signal or all of the 16 pixel signals individually. In this way, the evaluation board allows the ArraySL-4 to function as either a single channel or multi-pixel device respectively. There is on board regulation to provide the +/-3.3V and +36V for the preamplifier board power and bias.

This product works with the Array4-EVB-PreAmp (Sold Separately).  Additional details are available in the ArraySL Data Sheet.

3x3 matrix of Ceramic ArraySL-4's supplied with Cross-Wire Readout control electronics contained in an Aluminum housing.

Matrix9 provides a fully solid-state, four-side scalable detector for the readout of L(Y)SO scintillator arrays. It integrates all the electronics required to localize, time stamp and discriminate scintillation events.
Digitized event data comprising time, location and energy are sent to the host system via high speed USB interface.

The Matrix-EVB-16 is required for reading out between 1 and 16 Matrix 9 detector heads.  This is a separate purchase.

Addition details on the Matrix 9 are available HERE

** NOTE ** Pricing on the website is for single unit sales.  If you are interested in purchasing more than 2 units please contact SensL sales for volume discount.

The Matrix9 Coincidence Board (Matrix-EVB-16) supports up to 16 Matrix9 modules. It provides a common clock, retrieves and buffers event data, performs temporal coincidence analysis for events from different detector heads and interfaces with the host computer through a high speed USB connection.

A single Matrix-EVB-16 can support between 1 and 16 MatrixSL-9-30035 detector units.

Additional information is available HERE

The SensL MiniSL includes a MicroSL-30035-X08 SPM with a  transimpedance pre-amplifier, a Peltier cooler driver circuit to enable cooling and integrated power supply as standard. A variety of add-on options to enhance functionality are provided, including C-mount (male) adapter and a fiber coupler (adapter and fiber cable included). The SPM detector is mounted on a single stage Peltier cooler and housed in a hermetically sealed TO8 can. This allows greater performance over room temperature operation as the dark rate is reduced by over an order of magnitude.

Additional details are available HERE

The SensL MiniSL includes a MicroSL-10035-X08 SPM with a  transimpedance pre-amplifier, a Peltier cooler driver circuit to enable cooling and integrated power supply as standard. A variety of add-on options to enhance functionality are provided, including C-mount (male) adapter and a fiber coupler (adapter and fiber cable included). The SPM detector is mounted on a single stage Peltier cooler and housed in a hermetically sealed TO8 can.

Additional details are available HERE

C-Mount Adapter (male) Option for MiniSL Family

OPTIONAL:

20 pin Through Hole PGA connector for ArraySL-4-30035-CER